CD1-OPERA
CompactPCI Mobile Pentium® 4 CPU
CompactFlash, USB 2.0, 3 x Gigabit Ethernet and DVI-I Graphics on-Board
Equipped with the Intel® Mobile Pentium® 4 - M Processor up to 2.2GHz,
the CD1-OPERA is a powerful 6U (double size Eurocard)
CompactPCI® CPU board.
The board is provided with the chipset 845G(V), which contains an
embedded graphics controller. The DVI-I interface allows for attachment of
both, advanced (digital) and legacy (analog) flat panel displays and CRT
monitors. The mobile 0.13u processor reduces the power consumption
considerably, thus enabling a reliable passive heatsink for thermal discharge.
Three 2.0 USB ports allow for plug & play attachment of
a variety of peripheral devices. For high speed networking up to 1000Mbps,
the CD1-OPERA is equipped with three independent triple-speed Gigabit Ethernet controllers.
The PICMG® 2.16 standard (Ethernet over CPCI backplane) is also supported.
|
|
As mass storage interface, the CD1-OPERA comes equipped with an Ultra ATA/100 connector.
In addition, a receptacle for ATA CompactFlash cards allows utilization of a
silicon disk. The main memory is a SO-DIMM 200 form factor DDR-SDRAM module of up
to 1GB capacity.
The PCI bridge allows for configuring of the CD1-OPERA as a CompactPCI system
slot controller, or peripheral slot board in multi-processor applications.
Alternatively, either one PMC card socket, or two PC•MIP mezzanine module slots,
or a 2.5-inch hard disk module enable on-board expansion of the CD1-OPERA.
A local PXI controller is provided for measuring and testing applications.
The Phoenix BIOS is maintained by EKF.
In this way custom specific enhancements can be realized.
The CD1-OPERA is a high performance industrial CPU, suitable for stand-alone
applications as well as large CPCI systems.
|
|
CD1-OPERA - the Ultimate Industrial Pentium 4-M CPU Board
|
|
Feature Summary CD1-OPERA
|
|
Form Factor
|
Double size CompactPCI style Eurocard (160x233mm2),
front panel width 4HP (20.3mm)
|
|
Processor
|
Intel® Mobile Pentium® Processor 4 - M (Northwood® 0.13u generation),
400MHz PSB, 512KB second level cache, clock rate 1.7GHz (1.3V/30W), 2.2GHz (1.3V/35W)
|
|
Chipset
|
i845G(V) (Brookdale®) chipset consisting of:
-
82845G(V) Graphics/Memory Controller Hub (GMCH)
-
82801D I/O Controller Hub (ICH4)
-
2 x Firmware Hub (FWH) 82802 compatible
|
|
Memory
|
200-pin SO-DIMM socket (notebook style module), PC2100 DDR266-SDRAM,
1GB maximum capacity
|
|
Video I/O
|
Analog monitor and digital flat-panel display support by DVI-I connector
(front panel), up to 2048 x 1536 pixel 16M colours 85Hz refresh rate, incorporates
PanelLink Digital technology (Silicon Image)
|
|
USB I/O
|
Type A connector (front panel) USB 2.0, another two USB ports across rear I/O (J4)
|
|
Ethernet I/O
|
3 independent 10/100/1000Mbps Gigabit Ethernet controllers, 82540 chip,
2 x RJ-45 connectors available from the front panel, 1 x rear I/O
according to PICMG® 2.16 across J3
|
|
Legacy I/O
|
LPC Super-I/O controller on-board, COM1 (front panel), combined PS/2 keyboard and
mouse port (front panel), COM2, parallel port, floppy disk interface (rear I/O across J4)
|
|
IDE/ATA
|
-
Ultra ATA/100 44-pin connector (secondary IDE, master/slave)
-
CompactFlash socket for CFA ATA cards (secondary IDE, master)
-
Primary IDE port available across rear I/O (J4)
-
Primary IDE port optionally available for an on-board 2.5-inch hard disk
mezzanine module (CD1-4-OPERA)
|
|
PXI Interface
|
PCI eXtensions for Instrumentation Standard, Rev. 2.0 (rear I/O across J2)
|
|
Mezzanine I/O
|
Stuffed alternatively:
-
1 slot for a PMC module, I/O from the front panel and across J5 (e.g. CD1-1-OPERA)
-
2 slots for PC•MIP modules, I/O from front panel and across J5 (e.g. CD1-2-OPERA)
-
On-board 2.5" hard disk module (primary IDE)
-
Rear I/O transition board available (CDX-RIO)
|
|
Rear I/O
|
-
IDE, Floppy, USB2, USB3, LPT, COM2, GPIO (J4)
-
Gigabit Ethernet (J3)
-
Mezzanine Rear I/O (J5)
-
Rear I/O transition module available (CDX-RIO)
|
|
CompactPCI Bus
|
64-bit, 33/66MHz, PCI bridge HINT HB6 (PLX), configurable as CompactPCI
system slot controller (e.g. CD1-1-OPERA), or peripheral slot board (e.g. CD1-A-OPERA)
|
|
Hot Swap Function
|
Board installing and removing without adversely effecting a running system,
'Full Hot Swap' implementation according to CompactPCI Hot Swap Specification PICMG® 2.1
(for peripheral slot boards only, e.g. CD1-A-OPERA)
|
|
Typical Power Consumption
|
1.7GHz
modest load (WinXP)
full load (MaxPow80)
full load (PCMark2002)
|
3.3V
2.2A
2.2A
2.9A
|
5V
0.9A
5.4A
5.4A
|
2.2GHz
modest load (WinXP)
full load (MaxPow80)
full load (PCMark2002)
|
3.3V
2.2A
2.2A
2.9A
|
5V
1.1A
7.2A
7.2A
|
1.2GHz Battery Optimized Mode
modest load (WinXP)
full load (MaxPow80)
full load (PCMark2002)
|
3.3V
2.2A
2.2A
2.9A
|
5V
0.7A
3.2A
3.2A
|
|
BIOS
|
Phoenix BIOS 4.0 Rel.6.0, 8/16Mbit Flash (Dual Firmware Hub)
|
|
MTBF
|
88,000h
|
|
Ambient Temperature
|
- 0°C bis +60°C (Operation)
- -40°C bis +85°C (Storage)
|
|
Relative Humidity
|
5% to 95% (non condensing)
|
|
Altitude
|
-300m to +3000m
|
|
Shock
|
15g 0.33ms, 6g 6ms
|
|
Vibration
|
1g 5-2000Hz
|
|
Typical Calculating Performance
|
PCMark2002 under Windows 2000, CPU/MEM Score:
4132/3931 @1.7GHz, 5236/4152 @2.2GHz
|
subject to change
CD1-OPERA - Block Diagram Sheet 1
|
CD1-OPERA - Block Diagram Sheet 2
|
CD1-OPERA - Connector Orientation
|
CD1-OPERA with on-Board Hard Disk Module
|
Optional Hard Disk Module
|
CDX-RIO - Connector Orientation
|
|
Ordering Information |
|
Alias
|
Ordering No.
|
Short Description
|
|
OPERA
|
CD1-1-OPERA
|
6U CPCI CPU card, 1.7GHz Mobile Northwood P4, 512MB DDR SDRAM, 3 x USB,
2 x Gigabit Ethernet, 1 x PICMG® 2.16 Backplane Ethernet, Ultra ATA/100 IDE,
CompactFlash ATA slot, DVI-I video out,
KBD/mouse, COM1/2, floppy, 1 x PMC mezzanine slot,
CompactPCI system controller
|
|
OPERA
|
CD1-2-OPERA
|
Similar to CD1-1-OPERA, 2 x PC-MIP mezzanine slots
|
|
OPERA
|
CD1-3-OPERA
|
Similar to CD1-1-OPERA, w/o PICMG® 2.16 Backplane Ethernet (J3 not stuffed)
|
|
OPERA
|
CD1-4-OPERA
|
Similar to CD1-1-OPERA, with 2.5-inch hard disk mezzanine module
|
|
OPERA
|
CD1-A-OPERA
|
Similar to CD1-1-OPERA, but configured as CompactPCI peripheral board (slave CPU),
suitable for multi-processing applications
|
|
OPERA
|
CD1-B-OPERA
|
Similar to CD1-2-OPERA, but configured as CompactPCI peripheral board (slave CPU),
suitable for multi-processing applications
|
|
|
CD1-P22-OPERA
|
2.2GHz processor option
|
|
|
CD1-Z-OPERA
|
1GB memory option
|
|
RIO
|
CDX-1-RIO
|
6U, 4HP J4/J5 rear I/O transition module
|
|
RIO
|
CDX-2-RIO
|
6U, 8HP J4/J5 rear I/O transition module with rear I/O 2.5" hard disk module
|
|
RACK
|
CR7-1-RACK
|
19-" Rack 7U, 8 slots CompactPCI 6U backplane P1-P5 (rear I/O P3-P5),
power supply, floppy disk, hard disk, DVD-ROM
|
|
RACK
|
CR7-9-RACK
|
Option desktop case 7U
|
|
TIGER
|
DE2-2-TIGER
|
PMC module, SATA controller + 1.8-inch hard disk drive
|
|
|
280.7.400
|
External PS/2 keyboard/mouse Y-splitter-cable mini-DIN male to 2 x mini-DIN female
|
|
|
908.51.02.01
|
DVI-D to DVI-D cable assembly, 2m, connects the CD1-OPERA to DVI monitors (digital way)
|
|
|
908.57.02.01
|
DVI-I to HD DSUB15 cable assembly, 2m, connects the CD1-OPERA to VGA monitors (analog way)
|
|
|
908.57.12.01
|
DVI-I to VGA adapter (plug to receptacle), to be plugged onto the CD1-OPERA DVI
output, with HD DSUB15 socket, suitable especially for analog monitors
with attached VGA cable
|
|
